type r engine , brake and suspention swap!! attn: adtuning

Status
Not open for further replies.
J

joeyb16a

Guest
type r engine , brake and suspention swap!! attn: adtuning

my question is:

is it possible to do a 5 lugs type r conversion( with wheels)
suspention,brake, on my civic sir 99

i know there is no probleme for the engine and tranny
and how much would it cost
thanx

2nd question: is this good modif for a na type r and what power should i expect at the wheels
-je forged piston( higher compression)
-forged rod
-tada b spec cam
-ported&polished head
-oversized throttle body
-valve spring, reteiner
- test pipe and vtec controller
-spoon header
thanx
 
Re: type r engine , brake and suspention swap!! attn: adtun

Joey,

Looks like to have lots of $$$ to play with.. however, if you got that kind of cash this is what I think you consider(but lots of work).. it will kill any R... b20 block, b17a crank, custom length rods and pistons (it will give you a r/s ratio of about 1.72, wich = insane revs with no failure) keep you b16 head, get r cams and the whole motion assembly, put it together with a limited slip in a gsr tranny... oh yeah dont for get the fuel at least 310 cc injectors...

ps: I think Laminar is going to start to play around with theses set ups... should be killer!
 
Re: type r engine , brake and suspention swap!! attn: adtun

Hey Joeyb16a.
Well i dont work there but however i am his brother, For sure 100% you can put the 5 lug type R conversion (with wheels) suspention,brakes, on your civic sir 99.
As for the motor i have one in my Civic and it has 11:01 compression and a ported and polished intake and throttle body,Im not sure about the HP but its up there. I ran a 14.10 stock. Im not sure how many HP you'll have but id imagine that it would be allot. Its definately an awsome motor!!!!

97CivicType-R
you can contact Adtuning at 514-631-1312
 
Re: type r engine , brake and suspention swap!! attn: adtun

thanx
as soon as i get the piece and sell my engine im going to call
what can i put for 3000$ worth of mod??
i already have a catback and aem cai

i was first thinking about raising the compression with forged piston and rod
port&polised head with oversized throttle body and test pipe!!

then will fallow spoon header,toda specb cam, toda cam gear, valve spring and reteiner

my goal is around 200whp
 
Re: type r engine , brake and suspention swap!! attn: adtun

the type r setup you mentioned with those mods
should net about 200 hp at the wheels!
my canadien type r had 172 hp and 125 tq at
the wheels. it was stock.
11.5 to 1 compression would be amazing!
i will try to post a picture of my canadien
type r dyno run against my new jap spec
dyno run.(should happen this week).
Also make sure you properly dial in your cams
with the adjustable sprockets.(it makes all the difference)
 
Re: type r engine , brake and suspention swap!! attn: adtun

so basically the canadian type r with cam, camgear,headers,p&p head and 11.5.1 compression piston with forged rod would give me ~200whp
sent me your dyno chart id be intrested to see them
thanx
 
Re: type r engine , brake and suspention swap!! attn: adtun

The jap spec stock type r in my car now will go to the dyno
this week, then ill post both on this topic by the weekend
And as for 200 whp im positive.
 
Re: type r engine , brake and suspention swap!! attn: adtun

laminar check my post on the mugen engine and tell me what you think of it

title: gooing turbo or
 
200whp

how much do you guys think it can cost to get 200 NA whp on the b18c5?
 
Re: 200whp

id say even more if you put very goos stuff
ex:ntada b spec cam + cam gear already 2000$
spoon 4-2-1 headers 1000$$
its already 3000 and your far from 200whp
then you gotta to add reteiner and valve spring(600$) if you want to take the max capacity of your cam
then tune the ecu
 
Re: 200whp

Spoon headers,$1000.00 ????
I sell an amazing 4 into 1 race header
for $460.00.
To me springs and retainers are an
option. The stock type r revs to 8600
rpm and with those high perf. cams
max power is at aprox 9000 rpm.
Honda does always build there motors
with safety margine,and i dont think that
400 rpm would be above the safety limit.
The B16A setup i ran this year went to
9500 rpm plenty of times this year.
Im running type r valvetrain.
 
how much for mugen headers

how much will it cost for mugen headers for a b18 engine?
 
Re: how much for mugen headers

a mugen headers for b18c is around 975$ us!!!
 
headers

how much are the headers ???
you have headers for 460$ ill buy rite away what kind???
mugen???
does it fit on a b18?????
 
headers

Oups sorry i mean spoon headers....
you got them for 460$?
 
spoon header

sorry bro i dont think you can get spoon header for 450!!!!
its minimum 800$$

buy comptech there good or just but the one laminar have 4-1 race headers for around 400$$!!!
 
headers

so what kind of headers can i get for around 400$
u got a picture?
 
spoon

i heard headers on a type r are not worted the price!!!!
for around 400 you better keep your$$$
dc 4-1 goes for 600$$
comptech even more
save your money for toda b spec cam and a port and polished head!!!
then save again for mugen or spoon header
 
Status
Not open for further replies.
Back
Top